View MC145220EVK_79187.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document by MC145220EVK/D
MC145220 Evaluation Board Manual
INTRODUCTION
The MC145220EVK makes it easy to exercise features of the MC145220 and build PLLs which meet individual performance requirements. The EVK is controlled through menu driven software operating on an IBM PC or compatible. Other Motorola PLL EVKs (MC145190, MC145191, MC145192, MC145200, MC145201, MC145202) in up to three-board cascades can use the same program. Frequency defaults that apply to each are automatically selected. All board functions are controlled through the printer port of an IBM PC. Up to three different EVKs may be controlled at the same time from one printer port. The functional block diagram is given in Figure 1. This manual is divided into three sections. Section 1 describes the hardware, Section 2 describes the software, and Section 3 is the command summary.
All brand names and product names appearing in this document are registered trademarks or trademarks of their respective holders.
This document contains information on a new product. Specifications and information herein are subject to change without notice. REV 2 10/96
(c) Motorola, Inc. 1996 MOTOROLA
MC145220EVK 1
MC145220EVK TABLE OF CONTENTS
Section 1 - Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents of Evaluation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Production Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual Mode Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Reference Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Transfer from Computer to EVK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 2 - Software Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Uninstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alert and Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . `Define boards to program' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Help Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . `Select from the available options' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . `Available Boards' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . `MC145xxx Commands' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . `Initialization/System Setup Commands' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Output Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFin Frequency and Channel Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Default Low Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Function of Output A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change C Register and Prescale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change C Register, PDout Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change C Register, Phase Detector Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change C Register, Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change C Register, Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Output Port Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Crystal or Reference Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 3 - Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [A]! Set board A as target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [B]! Set board B as target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [C]! Set board C as target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [L]! Set to low freq. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [M]! Set to medium freq. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [H]! Set to high freq. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [W] Change default low frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Y] Change default medium frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Z] Change default high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [U]! Step frequency up by step size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [D]! Step frequency down by step size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [O] Set PLL output frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [F] Set REFin frequency and channel spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220EVK 2 5 5 5 5 5 7 8 8 8 9 11 11 13 14 14 14 14 14 14 15 15 15 18 18 19 20 20 20 20 22 23 24 25 26 27 28 29 30 31 32 33 33 33 33 33 34 34 34 35 36 36 36 37 38
MOTOROLA
MC145220EVK TABLE OF CONTENTS, continued
[E] Set function of output A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Data Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2]! fv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3]! fr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [N] Change C Register and Prescale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0] Change output A - (Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Reset output A to 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Set output A to 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1] Change output B (Out B) (not available on '220) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Reset output B to 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Set output B to 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2] Change PDout current with Output A defined as port (not available on '220) . . . . . . . . . . . . . . . . . . . [0]! 70% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! 80% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2]! 90% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3]! 100% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2] Change PDout current with Output A NOT defined as port (not available on '220) . . . . . . . . . . . . . . [0]! 25% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! 50% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2]! 75% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3]! 100% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2] Change PDout current (only available on '220) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! 5% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! 50% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2]! 80% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3]! 100% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3] Change phase detector select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! phi R & phi V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! PDout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3] Change phase detector (only available on '220) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! phi R & phi V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! PDout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [4] Change lock detect enable (not available on '220) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Output low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Enable output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [5] Change phase detector polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Non-invert PDout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Invert PDout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [6] Change standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Normal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [7] Change prescale (only available on '220) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Prescale 32/33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Prescale 64/65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [R] Set crystal/reference mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0]! Crystal mode, shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [1]! Crystal mode, active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [2]! Reference mode, REFin enabled, REFout low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [3]! Reference mode, REFout = REFin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [4]! Reference mode, REFout = REFin/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [5]! Reference mode, REFout = REFin/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [6]! Reference mode, REFout = REFin/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [7]! Reference mode, REFout = REFin/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [T]! Set target PLL on board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [P] Set output port address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOTOROLA 39 39 39 39 39 40 40 40 40 40 40 40 41 41 41 41 41 41 41 41 41 41 42 42 42 42 42 42 42 42 43 43 43 43 43 43 43 43 43 44 44 44 44 44 44 45 45 45 45 45 45 45 45 45 46 46
MC145220EVK 3
MC145220EVK TABLE OF CONTENTS, continued
[G] Change board definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [I]! Initialize board(s), write all registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [X]! Terminate demonstration program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [?]! View help screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220 PLL Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220 Power Supply and Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220EVK Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220EVK Signal Plot -- Dual Loop Mode Output at 70 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220EVK Signal Plot -- Single Loop Mode PLL on 805 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC145220EVK Signal Plot -- Single Loop Mode PLL on 738 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bill of Materials: MC145220 PLL Evaluation Board Rev. 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 46 46 46 47 47 48 49 50 50 51 52
MC145220EVK 4
MOTOROLA
SECTION 1 - HARDWARE
FEATURES
1. 2. 3. 4. 5. 6. 7. 8. The EVK is a complete working synthesizer, including VCOs. Board is controlled by an IBM PC-compatible computer through the printer port. Up to three boards can be operated independently through one printer port. A prototype area and mounting holes are provided for VCOs, mixers, and amplifiers. External reference input can be used. Five element loop filter is included. Frequency range of operation, step size and reference frequency can be changed in the control program. Lock Detect, Out A, and Out B on any single board are accessible through the printer port.
CONTENTS OF EVALUATION KIT
1. 2. 3. 4. 5. Assembled evaluation board. Nine-foot flat cable with four DB-25 male connectors. MC145220EVK manual. 3.5 PC-compatible disk containing compiled program. PLL device data sheets.
GETTING STARTED
To perform basic functions, do the following: 1. 2. 3. 4. 5. Plug in 12 volts at J8, observing the polarity marked on the board. Short circuit section 1 of the DIP switch (S1) and open circuit all other sections. Connect the supplied flat cable between the computer printer port and the DB-25 connector on the board (J9). Type PLL at the DOS prompt. Then press enter. Type the number that corresponds with the type of board given in the on-screen menu. The MC145220 may operate in single loop or dual loop mode. Then press Q.
You should now see the main menu displayed. There should be a signal present at J5 if single loop, or J12 if dual loop. The frequency will be the current output frequency given in the main menu. If the signal is not on the correct frequency, check to see if your printer port address is $278 (hexadecimal 278). If not, then select the P menu item and enter the correct address. After returning to the main menu, select the I menu item to send data to the board. You should now be on frequency.
MODIFICATIONS
The user may modify the hardware, such as utilizing a different VCO, by using the prototyping area of the board. After such modifications are made, the default values in the software may need to be changed. This is facilitated from the `Select from the available options' screen. Note that the on-board voltage regulators allow for a maximum VCO control voltage range of 0.5 - 4.5 volts.
MOTOROLA
MC145220EVK 5
Logic Control Switches 74HCT241, 74LS126 Buffer Logic Frequency Control Data External Reference 10.01 MHz TCXO 14.4 MHz TCXO REFin PDout MC145220 PLL Out A, Out B, Lock Detect Fin Loop Filter VCO 733 - 743 MHz VCO 790 - 820 MHz Loop Filter MC145220 PLL Fin
Parallel Port Connector
LO IF Single Loop Output 733-743 MHz
RF
Single Loop Output 790 - 820 MHz
Fc = 80 MHz
Dual Mode Output 60 - 80 MHz
(f - f) Amplifier
Figure 1. Evaluation Kit Block Diagram
MC145220EVK 6
MOTOROLA
TYPICAL PERFORMANCE
Typical performance applies only to the configuration as shipped. The MC145220EVK is shipped with V+ = 5 V. For lowest phase noise in single or dual loop mode, a 50 load must be connected to J12. Single Loop PLL Single Loop PLL Supply Voltage (J8) Supply Current (J8) (Note 1) Available Current (Note 2) Frequency Range (Note 3) Reference Frequency (M1) Temperature Stability (M1, - 30C to + 70C) Reference Frequency (M5) Temperature Stability (M5, - 30C to + 85C) TCXO Aging (M1, M5) Step Size Power Output Frequency Accuracy Reference Sidebands (Note 4) Phase Noise (100 Hz) Phase Noise (10 kHz) (Note 5) Switching Time (Note 6)
- 3.0 dBm 1.5 kHz - 57 dB - 65 dBc/Hz - 104 dBc/Hz 24 ms
Dual Loop PLL
11.5 - 12.5 V 177 mA
45 mA
733 - 743 MHz
790 - 820 MHz 10.01 MHz < 2.5 ppm
60 - 80 MHz
14.4 MHz < 2 ppm < 1 ppm / year 10 kHz
- 5.0 dBm 1.5 kHz - 74 dB - 56 dBc/Hz - 90 dBc/Hz 40 ms
N/A N/A
10 Hz 4.5 - 7.5 dBm
50 Hz
- 57 dB - 50 dBc/Hz - 89 dBc/Hz 45 ms
NOTES: 1. Supply current is current the board requires without user modifications. 2. Available current is the sum of currents available to the user (in the prototype area) from the 5 V and 8.5 V supply. The 12 V supply is not regulated. Current at 12 V is limited by the external power supply. If the on-board VCO and amplifier are disconnected from the power bus, more current can be drawn in the prototype area. The current flowing into U5 (the 8.5 V regulator) should not exceed 180 mA. This will limit temperature rise in U5. 3. Frequency ranges require use of the 5 V default charge pump supply voltage. 4. VCO sidebands on PLL at low step sizes (10 kHz) are limited by control line leakage of the VCO. Up to 24 nA of leakage has been seen. At higher step sizes (100 kHz and above), this effect is much less noticable. This did not affect PLL because its VCO leakage was less than 10 pA. 5. 10 kHz phase noise is limited by the PLL device noise. For low noise designs, the loop bandwidth is made narrower and the VCO is relied upon to provide the 10 kHz phase noise. This can be seen on the EVKs since the VCOs have much lower noise. 6. 10 MHz step, within 1 kHz of final frequency ('220). Due to the software architecture, when the user is measuring the switching time of a single board in dual loop mode, it takes 20 ms to load the data as compared to single loop mode, which takes 8 ms to load the data. This is a limitation of the software, not the IC. To find the actual PLL switching time, subtract 8 or 20 ms from the switching time stated in the table.
MOTOROLA
MC145220EVK 7
SUPPORT MATERIAL
The following documents are included in the appendix: 1. 2. 3. 4. 5. 6. Schematic diagram of MC145220EVK. Bill of materials. Parts layout diagram. Mechanical drawing of board. MC145220 data sheet. Typical signal plots.
PRODUCTION TEST
After assembly is complete, the following alignment and test is performed: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. The control program is started in '220 single loop mode. [L]! is selected to set PLL frequency to 733 MHz. Power is applied to the board. DIP switch section 1 is closed circuit with all others being open circuit. After attaching computer cable, [I]! is selected. Trim resistor VR1 is adjusted to obtain an output frequency at J5 of 733 MHz 500 Hz. Voltage at the control voltage test point (TP2) is measured. It must be > 0.5 V. [H]! is selected. Voltage at the control voltage test point (TP2) is measured. It must be < 4.4 V. [T]! is selected to toggle to PLL. [L]! is selected to set PLL frequency to 790 MHz. Voltage at the control voltage test point (TP9) is measured. It must be > 0.5 V. [H]! is selected to set PLL frequency to 820 MHz. Voltage at the control voltage test point (TP9) is measured. It must be < 4.4 V. [G] is selected and the board type is changed to '220 dual loop mode. [Q]!, then [I]!, is selected to initialize the dual mode output (J12) to 70 MHz. The frequency should be 70 MHz 50 Hz.
If in step 5 it isn't possible to obtain a signal on frequency, the adjustment screw in M1 may be turned for further frequency adjustment range. If neither adjustment works, [P] should be selected and the correct printer port address entered. [I]! is then selected to reload the data.
BOARD OPERATION
A computer is connected to the DB-25 connector J9. Data is output from the printer port. The printer card is in slot 0 using the default address in the control program. Data is sent to the PLL device (U1) through the DIP switch (S1), and 74HCT241 buffer (U2). D1, D2, D3, R7, R8, and R12 are in the data path between the 'HCT241 and PLL device. This limits the high level output voltage of the buffer. Voltage on PLL device inputs must be no greater than 0.5 V above V+. A '220 PLL has three output lines which are routed through a 74LS126 line driver (U3) back to the computer. U2, the 74HCT241, provides isolation and logic translation for PLL input lines. Logic translation is needed from the TTL levels on the printer port to the CMOS levels on the '220 inputs. A 12 V power supply should be used to power the board at J8 (Augat 2SV-02 connector). The 2SV-02 will accept 18-24 AWG bare copper power leads. No tools are needed for connection. If power is properly connected, LED D4 will be lit.
MC145220EVK 8 MOTOROLA
Power passes from J8 to U5 (LM317 regulator) configured as an 8.5 V regulator. 8.5 V powers the VCOs. Regulators U6 and U7 use the 8.5 V supply to produce 3 V and 5 V. The '220 board can use either to power the logic and charge pump. V+ voltage is selected by J11. U6 and U7 are cascaded with U5 to equalize their individual voltage drops. The '220 operates in both a single loop and dual loop mode. There are no component changes between the two modes. The differences are in the programming of the counters and the SMA connector that is used. The PLL loop is composed of the MC145220 (U1), 733 - 743 MHz VCO (M2), and a passive loop filter (R4, R5, C6, C7, C8). In single loop mode, output is taken from J5. A passive loop filter was used to keep the design simple, reduce noise, and reduce the quantity of traces susceptible to stray pickup. The PLL loop is composed of the MC145220 (U1), 790 - 820 MHz VCO (M3), and a passive loop filter (R22, R25, C24, C26, C30). In single loop mode, output is taken from J10. Dual mode output is the (f - f) frequency output from the mixer. It is low pass filtered (L1, L2, C15, C21, C22) then amplified (U4). The output is available at J12. Phase detector current is 2 mA. J1 is a removable jumper used for current measurement of V+. Two TCXOs, a Motorola Saber 14.4 MHz (M5), and Raltron 10.01 MHz (M1) are supplied. As shipped from the factory, the 10.01 MHz TCXO is in use. This allows both the 10 kHz and 10 Hz step sizes to be used with one TCXO. 10.01 MHz cannot be divided for larger step sizes such as 100 kHz. For larger step sizes use the Saber. Jumpers J3, J4, J13, and J14 determine which TCXO or the external reference input is in use.
DUAL MODE OUTPUT
The dual mode output (J12) is the difference frequency from mixing PLL and PLL. By using a reference frequency of 10.01 MHz, PLL can be operated with a 10.01 kHz step size and PLL with a 10 kHz step size. If both PLL and PLL step down in frequency, the mixed output will step up by 10 Hz. More information on the offset reference technique is in AN1277/D, Offset Reference PLLs for Fine Resolution or Fast Hopping. The block diagram, formulas, and an example are shown in Figure 2.
10.01 kHz R COUNTER / 1000
PHASE DETECTOR
VCO 730.7 - 740.7 MHz
PLL
REFERENCE 10.01 MHz
/N COUNTER
N = 73,001 - 74,000
f
(f - f) MIXER N = 79,075 - 82,074 60 - 80 MHz (10 Hz STEPS)
PLL
/ N COUNTER
f
R COUNTER / 1001
10 kHz
PHASE DETECTOR
VCO 790.7 - 820.7 MHz
Figure 2. Dual Mode Block Diagram
MOTOROLA MC145220EVK 9
PLL f = N (10.01 kHz) f = 10.01 kHz 74,000 - r(f - f) 10 Hz f = 10 kHz
PLL f = N (10 kHz) w(f - f) + 740 kHz +N 10 kHz w(f - f) 10 kHz
N = 74,000 -
r(f - f) 10 Hz
N = N + 74 + (f - f) = w(f - f) + r(f - f)
(f - f) = Desired Output Frequency w(f - f) = Output Frequency Portion that Divides Evenly by 10 kHz r(f - f) = Remainder from Output Frequency Division by 10 kHz Dual Mode Formulas
Example: Synthesize 76.849 930 MHz r(f - f) = 9.930 kHz, 9.930 kHz = 73,007 10 Hz 76.840 MHz = 80,765 10 kHz w(f - f) = 76.840 MHz
N = 74,000 -
f = 73,007 (10.01 kHz) = 730.800 070 MHz
N = 73,007 + 74 +
f = 80,765 (10 kHz) = 807.650 000 MHz
(f - f)= 807.650 000 MHz - 730.800 070 MHz = 76.849 930 MHz
MC145220EVK 10
MOTOROLA
EXTERNAL REFERENCE INPUT
To use an external reference, disconnect J3, J4, J13, and J14. Use a reference signal at J2 which complies with data sheet requirements. Then modify the reference frequency in the program main menu to reflect the changes made (F menu item).
DATA TRANSFER FROM COMPUTER TO EVK
To control the serial input EVK with the parallel printer port, a conversion is done. Printer cards are designed to output eight bits through eight lines. A bit mask is used to obtain the bit combination for the three required output lines (Data, Clock, Load). As bytes are sent to the printer card in sequence, it appears to be a serial transfer. The printer port is used because data transfer using the serial port would be much slower. A standard IBM PC can support a parallel port data rate of 4.77 MHz. IBM PCs and compatibles can accept up to three printer port configurations. These ports are called LPT1, LPT2, and LPT3. Each printer port has a unique address. Two sets of addresses are in common use. One set applies to IBM PC XT, AT, and clones. The other is for the PS 2 line. To load data into the EVK, the correct address must be selected. The program default is $278. If $278 is not the address in use, it must be modified by entering the P menu item in the main menu. All allowed addresses given in hexadecimal are as follows: Label LPT1 LPT2 LPT3 IBM PC and Clones 278 378 3BC PS 2 3BC 378 278
Up to three EVK boards can operate independently from one printer port. All lines on the printer port are connected to every EVK. Even with three boards operating, only three output lines (Clock, Data, and Load) from the printer card are used. If two boards are controlled together, data for the second board is received from the Output A of the first. Output A is a configurable output on '220 devices, which in this case is used to shift data through chip 1 into chip 2. Output A and Data are connected using a printer port input line. This was done to avoid connecting extra wires. Fortunately not all port input lines are needed for computer input. Load and Clock are common to both boards. A three-board cascade is handled similarly to a two-board cascade. Out A on the first board is fed to Data on the second. Out A on the second connects to Data on the third. Instructing the program on the quantity of boards connected together allows it to modify the number of bits sent. All boards have a DIP switch S1 which gives each a unique address. The configuration menu is used to tell the program what type of board is connected at a board address. Switch positions for all possible addresses are given in Figure 3.
MOTOROLA
MC145220EVK 11
Single Board Operation 1 Closed Open 2 3 4 5 6 7 8
Two- or Three-Board Cascade Board A 1 Closed Open 2 3 4 5 6 7 8
Board B 1 Closed Open 2 3 4 5 6 7 8
Board C 1 Closed Open 2 3 4 5 6 7 8
Figure 3. Switch Positions In Figure 3, DIP switch sections 6, 7, and 8 allow the computer to read Out A, Lock Detect, or Lock Detect from the PLL device. Each of the inputs can only be read on one board at a time, but each item could be read on a different board. In a three-board cascade, Out A could be read from the first board, Out B from the second, and Lock Detect from the third. There is no way to determine the board address of a particular input with software. The control program does not make use of these inputs; however, source code could be modified as required. Pin assignment on the printer port connector is: Label Out A Out B Lock Detect Pin Number 12 13 15
MC145220EVK 12
MOTOROLA
PRINTER PORT CONFIGURATION
Printer port outputs on an IBM PC or clone use TTL-LS logic levels. Inputs are one TTL-LS load. Signal lines can be used for any purpose. The standard names, direction of data flow, true and inverted data are shown in Figure 4.
Signal Name - Strobe + Data Bit 0 + Data Bit 1 + Data Bit 2 + Data Bit 3 + Data Bit 4 + Data Bit 5 + Data Bit 6 Printer + Data Bit 7 - Acknowledge + Busy + P. End (out of paper) + Select - Auto Feed - Error - Initialize Printer - Select Input Ground
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 - 25
IBM Printer Port
Figure 4. Printer Port Data Lines
Pin numbers for the port connector are shown in Figure 5.
13 (front view) 1
25
14
Figure 5. DB-25 Male Connector
MOTOROLA
MC145220EVK 13
SECTION 2 - SOFTWARE DESCRIPTIONS
INTRODUCTION
The MC145xxx PLL software is provided to demonstrate the capabilities of the MC145xxx family of PLLs. The family includes the following devices:
PURPOSE
The user guide for the MC145xxx PLL software familiarizes the user with the use and capabilities of the program referred from here on as PLLDEMO Version 4.0. The guide covers the user interface and a summary of the commands that are available. The user should read the data sheet of the PLL frequency synthesizer of interest before using the software.
DESCRIPTION
The PLL software: * is a Pascal program developed with Borland Turbo Pascal v7.0. * runs under MS-DOS. * is a character-based, menu-driven program.
USER INTERFACE
The user interface consists of numerous character-based, menu-driven screens which are displayed below. Each screen is shown, along with a description of its purpose. Note that all screen shots shown are a representative sample of the program. They are provided to familiarize the end user with the program.
INSTALL
To install this program, create a directory called "PLLEVAL". Change directories into "PLLEVAL" and copy PLL.exe into this directory.
MC145220EVK 14
A A AAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Board Description Low voltage version of the '191 Low voltage version of the '201 MC145220 in Single Loop Mode MC145220 in Dual Loop Mode
MOTOROLA
Table 1.
UNINSTALL
To uninstall this program, change directories into "PLLEVAL" and type "erase*.*". After this command, change out of directory "PLLEVAL" and type "erase PLLEVAL". Note: If you are in Windows 3.X or Windows 95, this program adds no entries into .ini or Registry files. It is recommended that you have the PLL program running while you are reviewing this manual. Due to the number of screens that may be involved in your evaluation, following the connections, screens, and commands is easier when the manual and program are used together.
CONVENTIONS
Some of the PLLDEMO screens are necessarily "busy". Because of this, the program follows several conventions to help the user quickly absorb the screen information. These conventions are briefly described on a help screen that is available throughout the program. Type the help command, [?], at any time to view the help screen. The conventions are as follows: 1. Command keys are surrounded by [ ]s. Type the letter between the [ ]s to execute the command. [ ]s are followed by a description of the command. 2. [-] indicates a command not available to the user. Commands become available when they are applicable to the currently targeted board. 3. [ ]s followed by an ! indicate the command will execute immediately. Otherwise a submenu is displayed from which further choices may be made. 4. If no changes are desired to an input field, leave the field blank. The previous value will then be used for that field. Type the TAB key to move to the next input field, or shift-TAB to move to the prior input field. Type RETURN to store the new input values while remaining on the same screen. Type Q to store the new values and return to the prior screen. 5. All numbers are entered as decimal values unless otherwise noted. A $ followed by a value indicates the value is in hexadecimal format. The output port address is in hexadecimal format. 6. The second line from the top of screen (screen title) states the purpose of the screen. 7. Screen information that can be changed by the user is displayed in bold or reverse video. 8. Commands are case independent. X is the same as x. 9. Frequencies are entered as two numbers, and displayed as one. The two input numbers represent the desired frequency in MHz, and in kHz. These input values are added together to obtain the final frequency. Leave either input field blank to retain the prior value for that portion of frequency.
ALERT AND ERROR MESSAGES
This program contains two types of messages that appear when conditions warrant. (See Table 2.) 1. Alert Messages. These messages alert you that though the current values are valid, you are unable to continuously increment the A and N counters. Hit any key to remove these messages and continue with the program. There are some instances of the alert messages where you may have to hit any key twice to remove the message. 2. Error Messages. These are messages that indicate you have selected conditions that are outside of the valid parameters of the IC. After hitting any key to continue, the invalid parameters you selected will change back to the default parameters of the program. You may then enter another value to continue your evaluation. There are some error messages where you may have to hit any key twice to remove the message.
MOTOROLA
MC145220EVK 15
AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A
Table 2. Error Messages Category Validation Requirements Corresponding Error Message REFin Frequency* 1) Value must be 27 MHz and REFin frequency must be 1 MHz 1 MHz and 27 MHz 2) Divide ratio (value converted to kHz/step size in kHz): a) Must be 8191 REFin/channel spacing must be 8191 b) Must be an integer (there must REFin frequency is not a multiple of the be no fractional result of the step size division) c) Must be in range: i) = 1 or 5 ('190, '191, '192, REFin/channel spacing must be 5 '200, '201, '202) or 1 ii) = 1 or be 10 ('220S, '220D) REFin/channel spacing must be 10 or 1 Step Size* 1) Value must be: a) 120 Hz and 2 MHz Step size must be 120 Hz and ('190, '191, '200, '201, '202) 2 MHz b) 120 Hz and 1 MHz Step size must be 120 Hz and ('192, '220S, '220D) 1 MHz VCO Frequencies 1) Value must be: a) 100 MHz and 1100 MHz VCO frequency must be ('190, '191, '192) 100 MHz and 1100 MHz b) 500 MHz and 2000 MHz VCO frequency must be ('200, '201, '202) 500 MHz and 2000 MHz c) 40 MHz and 1100 MHz VCO frequency must be ('220S) 40 MHz and 1100 MHz d) 60 MHz and 80 MHz ('220D) VCO frequency must be 60 MHz and 80 MHz (limited by EVK) 2) Divide ratio (value converted to VCO frequency is not evenly divisible kHz/step size in kHz) must be an by current step size integer (this step skipped for '220D) -OR- VCO frequency is not evenly divisible by current step size (freq. now n/a) 3) N Counter must be A Counter Divide ratio is invalid, N Counter must (this step skipped for '220D) be A Counter -OR- Divide ratio is invalid, N Counter must be A Counter (freq. now n/a)
MC145220EVK 16
Continued on next page
MOTOROLA
AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA
Category Validation Requirements Corresponding Error Message VCO Frequencies 4) Divide ratio must be: (this step skipped for '220D) a) 262,143 ('190, '191, '192, '200, '201, '202, '220S with prescale = 64) b) 131, 071 ('220S with prescale = 32) Step Up or Step Down 1) VCO output frequency <> - 999.99 (this is the number used to represent n/a) Illegal A and N Counter divide value, value must be 262,143 -OR- Illegal A and N Counter divide value, value must be 262, 143 (freq. now n/a) Illegal A and N Counter divide value, value must be 131,071 -OR- Illegal A and N Counter divide value, value must be 131.071 (freq. now n/a) VCO frequency is invalid
*NOTE: REFin and step size are NOT validated on the '220D board. These validation sequences may not be appropriate for the MC145220D.
Continued from previous page
A A A A A A AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A
Category VCO Frequencies 1) Divide ratio must be (violation produces only an alert message, value is allowed): (this step skipped for '220D) a) 4032 ('190, '191, '192, '200, '201, '220S with prescale = 64) b) 992 ('220S with prescale = 32) A and N Counter divide value is < 4032, may be gaps in band coverage A and N Counter divide value is < 992, may be gaps in band coverage
MOTOROLA MC145220EVK 17
Table 3. Alert Messages Validation Requirements Corresponding Alert Message
SCREENS `Define boards to program'
The first screen the user sees when the program begins has a screen title of `Define boards to program'. This screen is used to define which boards are connected to the LPT1 printer port of the computer. Refer to the hardware setup section to determine how to cascade the evaluation boards. This screen is also available from the main menu. The user may return to this screen by depressing [Q] to change the boards that are connected to the computer. The screen is divided into two sections. The upper section shows the current board type settings while the lower section allows the user to define a board's type and position in the cascade connection. Notice the section labeled `Available Boards:' shows three labels, one for each board that may be cascaded. When the program first starts up it shows `N/A' (not applicable) after each label. The user must enter the boards contiguously. Initially the program requests for the user to enter board A's type. This is signified by A (in the screen below) being set to A. The user can the select the board type for board A by typing the corresponding command. Once board A's type is selected, A automatically increments to B and the process may be repeated. Once all boards have been correctly defined, the user may select [Q] which sends default data to the boards and continues to the next screen. NOTE: Before selecting [Q], the user should insure that the DIP switch settings shown in Figure 2 are correct. If a board is incorrectly identified, select the board that is not correctly defined by typing the corresponding board letter ([A], [B], or [C]). The user may then reselect the board's type. Once the board has been identified, the user may select the letter ([A], [B], or [C]) of the board followed by [S] to change hardware- dependent variables for that board. [X] can be selected to exit the program completely. [?] can be selected to view the help screen.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Define boards to program Available Boards: Brd [A]!: N/A Brd [B]!: N/A Brd [C]!: N/A -------------------------------------------------------------------------------- Board A is: [-]! [1]! [2]! [3]! [4]! no board MC145190 MC145191 MC145192 MC145200 [5]! [6]! [7]! [8]! MC145201 MC145202 MC145220 Single MC145220 Dual
[-] Boards defined, Continue
[X]! Terminate demonstration program. [?]! View help screen.
MC145220EVK 18
MOTOROLA
Help Screen
This is the help screen for the program. It is available from any point throughout the program. A short list of the interface conventions are presented on this screen. [X] can be selected to exit the program completely. [Q] can be selected to exit the help screen.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 1) Command keys are surrounded by []'s. Type the letter between the []'s to execute the command. []'s are followed by a description of the command. 2) [-] indicates a command not available to the user. 3) []'s followed by an ! indicate the command will execute immediately. Otherwise a sub menu will be displayed. 4) If no changes are desired to an input field, type the TAB key to move to the next input field. The previous value will be used for that field. 5) All numbers are entered as decimal values unless otherwise noted. A $ followed by a value indicates the value is in hexadecimal format. 6) The second line from the top of screen (screen title) states the purpose of the screen. 7) Screen information that can be changed by the user is displayed in bold or reverse video. 8) Commands are case independent. X is the same as x. [X]! Terminate demonstration program. [Q]! Quit help screen.
To access this screen, press shift + ? on your keyboard while within any screen in the program.
MOTOROLA
MC145220EVK 19
`Select from the available options'
This is the main screen of the program. This is where the user enters commands to demonstrate the capabilities of the various boards connected to the computer. The title of the screen is `Select from the available options'. This screen is broken down into three sections: `Available Boards' This section displays the board types that are connected to the computer. It also designates which board is the currently selected `target' board. This is the board that will receive the commands from `MC145xxx Commands' section. This section also provides the ability to change the targeted board. Type the target board command ([A], [B], or [C]) to target that particular board. `MC145xxx Commands' This section is further divided into three subsections. Each subsection contains commands that can be sent to the `target' board to demonstrate its capabilities. Each of these commands is described in full in the Command Summary. The first subsection, `MC145xxx Frequency Commands', contains commands that are used to modify the PLL frequency in some way. These commands are available for all possible target board types. In the top line of this section, `Current Output Frequency is 70 MHz' designates what the frequency is for the currently targeted board. This value is dynamic. On the lines below this, 60 MHz is the current setting for the default low frequency. 70 MHz is the current setting for the default medium frequency. 80 MHz is the current setting for the default high frequency. The second subsection, `MC145xxx Additional Commands', contains commands that are used to further modify the currently targeted board. These commands also work with all of the MC145xxx board types. The third subsection, `MC145220 EVK - Single Specific Commands', are only displayed when the MC145220EVK in single loop mode is the currently targeted board. This section shows commands that are specific to this board. This is required since this board contains the equivalent of two PLLs. The command letter for `Set target PLL on board' is [T]!. In single loop mode, the user may toggle between PLL and PLL on the MC145220EVK by using this command. Feedback is given to the user as to whether PLL or PLL will be accessed. See near the top of the screen on the line titled "Available Boards - Current target board is: ..." `Initialization/System Setup Commands' This section contains commands that are used to initialize all boards connected to the computer or to set up the computer.
MC145220EVK 20
MOTOROLA
`Select from the available options' (continued)
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Select from the available options Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- MC145xxx Frequency Commands - Current Output Frequency is 70 MHz [L]! Set to low freq. 60 MHz [W] Change default low freq. 70 MHz [Y] Change default med. freq. [M]! Set to med. freq. [H]! Set to high freq. 80 MHz [Z] Change default high freq. [U]! Step frequency up by step size [O] Set PLL output frequency [D]! Step frequency down by step size [F] REFin freq. & channel spacing MC145xxx Additional Commands [E] Set function of output A [N] Change C register and Prescale [R] Set crystal/reference mode - Current mode is Ref. mode, REFout low -------------------------------------------------------------------------------- Initialization/System Setup Commands: [P] Set output port address - Current address is $278 [G] Change board definitions [I] Initialize board(s), Write all registers [X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen you see above. This sequence to access the "Select from the available options" screen works the same for any selected board in the "Define boards to program" screen.
MOTOROLA
MC145220EVK 21
PLL Output Frequency
This is the resulting screen that is displayed after the user selects the `[O] Set PLL output frequency' command. The user is prompted to enter the new frequency. The current output frequency is automatically retained if the user hits return or [Q] without entering a value.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Set PLL output frequency Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Input new frequency in integer values of MHz, kHz, and Hz. Original program default PLL output frequency is 70 MHz Current PLL output frequency is 70 MHz Original program default frequency range is 60 MHz to 80 MHz Current frequency range is 60 MHz to 80 MHz Frequencies outside the program default frequency range will NOT be accepted. New PLL frequency: 70 MHz + 000 kHz + 000 Hz [TAB] to move to next field [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen shown above, press [O]. This sequence to access the "Set PLL output frequency" screen works the same for any selected board in the "Define boards to program" screen.
MC145220EVK 22
MOTOROLA
REFin Frequency and Channel Spacing
This is the resulting screen that is displayed after the user selects the `[F] Set REFin freq. and channel spacing' command. The user is prompted to enter the new REFin frequency and channel spacing values, or leave the fields blank to retain the prior settings. In '220 dual mode, the user does not have the option of changing REFin frequency or channel spacing.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 REFin frequency and channel spacing Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Due to the complexity of error checking in Dual Mode, REFin frequency may not be modified. The REFin frequency is 10.01 MHz Due to the complexity of error checking in Dual Mode, channel spacing may not be modified. The channel spacing is 10 Hz
[Q]
to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen shown above, press [F]. This sequence to access the "REFin frequency and channel spacing" screen works the same for any selected board in the "Define boards to program" screen.
MOTOROLA
MC145220EVK 23
Set Default Low Frequency
This is the resulting screen that is displayed after the user selects the `[W] Change default low freq.' command. The user is prompted to enter the new default low frequency value. Entering a new value does not change the current output frequency of the target board. Changing the low frequency simply adjusts the low frequency setting available from the main menu. The `[L]! Set to low freq.' command changes the current output frequency. The screen is similar for the Y and Z commands except that the prompts specify medium or high frequency, respectively.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Set default low frequency Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Input new default low frequency in integer values of MHz, kHz, and Hz. Original program default low frequency is 60 MHz Current low frequency is 60 MHz New default low frequency: 60 MHz + 000 kHz + 000 Hz [TAB] to move to next field [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen shown above, press [W]. This sequence to access the "Set default low frequency" screen works the same for any selected board in the "Define boards to program" screen.
MC145220EVK 24
MOTOROLA
Set Function of Output A
This is the resulting screen that is displayed after the user selects the `[E] Set function of Output A' command. The user is provided a submenu to select from. The current setting for the function of Output A is displayed as Port, Data Out, fv or fr. The user may choose from the listed commands to adjust this setting.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Set function of Output A Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Set Output A function - Currently: Data Out [0]! Port [1]! Data Out [2]! fv [3]! fr [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen shown above, press [E]. This sequence to access the "Set function of Output A" screen works the same for any selected board in the "Define boards to program" screen.
MOTOROLA
MC145220EVK 25
Change C Register and Prescale
This is the resulting screen that is displayed after the user selects the `[N] Change C Register and Prescale' command. The user is provided a submenu to select from. Each submenu option also shows a submenu. Note that in '220 dual mode, some options are deleted. This is notated with the [-] symbol.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Change C Register and Prescale Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Change C register: [-] PDout Current Step Size [-] Output B - (Out B) [2] PDout Current - (PDout) [3] Phase Detector Select - (PDA/B) [-] Lock Detect Enable - (LDE) [5] Phase Detector Polarity - (POL) [6] Standby - (STBY) Change Prescale: [7] Prescale [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen shown above, press [N].
MC145220EVK 26
MOTOROLA
Change C Register, PDout Current
This is the resulting screen that is displayed after the user selects the `[N] Change C Register and Prescale' and then the `[2] Change PDout Current' command. The user is provided a submenu to select from. This submenu contains commands to change the PDout current settings. The screen is slightly different depending on whether Output A is defined as a port or not. See command [E] from the main menu. Note in '220 dual mode, PDout current for PLL and PLL is modified simultaneously by the software program. The current PDout setting is displayed as `5%', `50%', `80%', or `100%'. The user can select the [0], [1], [2], and [3] menu options to change the percent of PDout current. If the [Q] command is selected, then the user is returned to the main menu.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Change C Register, PDout Current Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Evaluation program modifies PDout Current on both PLL's for this board. Change C Register, PDout Current - Currently: 100% [0]! 5% [1]! 50% [2]! 80% [3]! 100% [Q] to return to previous menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. In this screen, press [N]. This will place you in the "Change C Register and Prescale" screen. To access the screen above, press [2].
MOTOROLA
MC145220EVK 27
Change C Register, Phase Detector Select
This is the resulting screen that is displayed after the user selects the `[N] Change C Register and Prescale' and then the `[3] Change phase detector select' command. The user is provided a submenu to select from. This submenu contains commands to toggle the phase detector setting. The current phase detector setting is displayed as `phi R & phi V' or `PDout', depending on the setting. The user can select the [0] and [1] menu options to toggle the phase detector select setting. If the [Q] command is selected, then the user is returned to the main menu.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Change C Register, Phase Detector Select Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Evaluation program modifies Phase Detector Select on both PLL's for this board. Change C Register, Phase Detector Select - Currently: PDout [0]! phi R & phi V, phi R & phi V [1]! PDout, PDout [Q] to return to previous menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. In this screen, press [N]. This will place you in the "Change C Register and Prescale" screen. To access the screen above, press [3]. This sequence to access the "Change C Register, Phase Detector Select" screen works the same for any selected board in the "Define boards to program" screen.
MC145220EVK 28
MOTOROLA
Change C Register, Polarity
This is the resulting screen that is displayed after the user selects the `[N] Change C Register and Prescale' and then the `[5] Change polarity of phase detector' command. The user is provided a submenu to select from. This submenu contains commands to toggle the polarity setting. The default '220 dual setting of the polarity is displayed as `Non-invert PDout and PDout, do not interchange phi R, R & phi V, V '. The user can select the [0] and [1] menu options to toggle the polarity setting. If the [Q] command is selected, then the user is returned to the main menu.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Change C Register, Polarity Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Evaluation program modifies Polarity on both PLL's for this board. Change C Register, Polarity - Currently: Non-invert PDout [0]! Non-invert PDout and PDout, do not interchange phi R, R & phi V, V [1]! Invert PDout and PDout, interchange phi R, R & phi V, V [Q] to return to previous menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. In this screen, press [N]. This will place you in the "Change C Register and Prescale" screen. To access the screen above, press [5]. This sequence to access the "Change C Register, Polarity" screen works the same for any selected board in the "Define boards to program" screen.
MOTOROLA
MC145220EVK 29
Change C Register, Standby
This is the resulting screen that is displayed after the user selects the `[N] Change C Register and Prescale' and then the `[6] Change standby' command. The user is provided a submenu to select from. This submenu contains commands to toggle the standby state setting. The standby state setting is displayed as `Normal operation' or `Standby', depending on the current setting. The user can select the [0] and [1] menu options to toggle the standby state setting. If the [Q] command is selected, then the user is returned to the main menu.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Change C Register, Standby Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Evaluation program modifies Standby on both PLL's for this board. Change C Register, Standby - Currently: Normal Operation [0]! Normal operation [1]! Standby [Q] to return to previous menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. In this screen, press [N]. This will place you in the "Change C Register and Prescale" screen. To access the screen above, press [6]. This sequence to access the "Change C Register, Standby" screen works the same for any selected board in the "Define boards to program" screen.
MC145220EVK 30
MOTOROLA
Set Output Port Address
This is the resulting screen that is displayed after the user selects the `[P] Set output port address' command. The user is prompted to enter the new output port address in hexadecimal. This should be the port address of the LPT1 printer port for the user's computer. The original program default port address and the current setting are displayed. Enter the new output port address in hexadecimal format.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Set output port address Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Input new output port address in hexadecimal. Original program default port address is $278 Current port address is $278 New output port address: $278 [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. To access the screen above, press [P]. This sequence to access the "Set output port address" screen works the same for any selected board in the "Define boards to program" screen.
MOTOROLA
MC145220EVK 31
Set Crystal or Reference Mode
This is the resulting screen that is displayed after the user selects the `[R] Set crystal/reference mode' command. The user is provided a submenu to select from. This submenu contains commands to change the crystal/reference mode. The current reference mode is displayed as `Crystal mode, Shutdown'; `Crystal mode, Active'; `Reference mode, REFin enabled, REFout low'; `Reference mode, REFout = REFin'; `Reference mode, REFout = REFin/2'; `Reference mode, REFout = REFin/4'; `Reference mode, REFout = REFin/8'; or `Reference mode, REFout = REFin/16', depending on the current setting. The user can select the [0] to [7] menu options to change the crystal/reference mode setting. If the [Q] command is selected, then the user is returned to the main menu.
Welcome to MC145xxx EVK Demonstration Program, rev 4.0 Set crystal or reference mode Available Boards - Current target board is: A, MC145220 Dual Brd [A]!: MC145220 Dual Brd [-]!: N/A Brd [-]!: N/A -------------------------------------------------------------------------------- Set crystal or reference mode - Currently: Ref. mode, REFout low [0]! Crystal mode, Shutdown [1]! Crystal mode, Active [2]! Reference mode, REFin enabled, REFout low [3]! Reference mode, REFout = REFin [4]! Reference mode, REFout = REFin/2 [5]! Reference mode, REFout = REFin/4 [6]! Reference mode, REFout = REFin/8 [7]! Reference mode, REFout = REFin/16 [Q] to return to main menu
[X]! Terminate demonstration program. [?]! View help screen.
This screen shot is a representative sample of the screens within this program. To access this screen with the MC145220 Dual EVK selected in the "Define boards to program" screen, from within the "Define boards to program" screen, press [Q]! . This will place you in the "Select from the available options" screen. Select [R], which will place you in the "Set crystal or reference mode" screen you see above. This sequence to access the "Set crystal or reference mode" screen works the same for any selected board in the "Define boards to program" screen.
MC145220EVK 32
MOTOROLA
SECTION 3 - COMMAND SUMMARY
[A]! Set board A as target
To access this command in the program, at the DOS prompt, type "PLL". This is the opening default screen.
See page 18 of this document for a sample screen shot of this command.
This command sets the target board to the board shown as A. This means that the commands that follow will affect board A only. The user is informed of, and may modify, the target board in any screen of the program except the help screen. This is strictly an internal program command and has no effect on the MC145xxx EVKs connected to the computer.
[B]! Set board B as target
To access this command in the program, at the DOS prompt, type "PLL". This is the opening default screen.
See page 18 of this document for a sample screen shot of this command.
This command sets the target board to the board shown as B. This means that the commands that follow will affect board B only. The user is informed of, and may modify, the target board in any screen of the program except the help screen. This is strictly an internal program command and has no effect on the MC145xxx EVKs connected to the computer.
[C]! Set board C as target
To access this command in the program, at the DOS prompt, type "PLL". This is the opening default screen.
See page 18 of this document for a sample screen shot of this command.
This command sets the target board to the board shown as C. This means that the commands that follow will affect board C only. The user is informed of, and may modify, the target board in any screen of the program except the help screen. This is strictly an internal program command and has no effect on the MC145xxx EVKs connected to the computer.
[L]! Set to low freq.
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [L]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command is used to set the frequency of the currently selected board to the currently defined low value. This value can be changed via the [W] command. This is accomplished by correctly adjusting the A register for the targeted board. If the current EVK is the MC145220 and the board is in DUAL mode, then the currently targeted PLL on the board is set to the specified low frequency. Otherwise, if the board is in SINGLE mode, both on- board PLLs are set to the new frequency.
MOTOROLA MC145220EVK 33
[M]! Set to medium freq.
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [M]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command is used just as the [L]! command except that the defined medium frequency value is used. This default value can be changed by selecting command [N]. Reference [L]! command for further details.
[H]! Set to high freq.
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [H]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command is used just like the [L]! command except that the defined high frequency value is used. This default value can be changed by selecting command [W]. Reference [L]! command for further details.
[W] Change default low frequency
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [W] is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command prompts the user to input a decimal value in MHz for the default low frequency. The program default low value is displayed along with the current value. The user may leave the low frequency value as is by entering return without a value. The program low default value is dependent on the targeted board type. (See Table 4.) This value is not sent to the board immediately. It is the value that is sent to the board when the [L] command is executed.
A AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Program Default Low Frequency 741 MHz 733 MHz 733 MHz 1482 MHz 1466 MHz 1466 MHz MC145220 in Single Loop Mode MC145220 in Dual Loop Mode 733 MHz (PLL) 790 MHz (PLL) 60 MHz
MC145220EVK 34 MOTOROLA
Table 4.
[Y] Change default medium frequency
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [Y] is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command prompts the user to input a decimal value in MHz for the default medium frequency. The program default medium value is displayed along with the current value. The user may leave the medium frequency value as is by entering return without a value. The program medium default value is dependent on the targeted board type. (See Table 5.) This value is not sent to the board at this time. It is the value that is sent to the board when the [M] command is executed. Table 5.
A AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Program Default Medium Frequency 746 MHz 738 MHz 738 MHz 1492 MHz 1476 MHz 1476 MHz MC145220 in Single Loop Mode MC145220 in Dual Loop Mode 738 MHz (PLL) 805 MHz (PLL) 70 MHz
MOTOROLA MC145220EVK 35
[Z] Change default high frequency
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [Z] is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command prompts the user to input a decimal value in MHz for the default high frequency. The program default high value is displayed along with the current value. The user may leave the high frequency value as is by entering return without a value. The program high default value is dependent on the targeted board type. (See Table 6.) This value is not sent to the board immediately. It is the value that is sent to the board when the [L] command is executed. Table 6.
A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Program Default High Frequency 751 MHz 743 MHz 743 MHz 1502 MHz 1486 MHz 1486 MHz MC145220 in Single Loop Mode MC145220 in Dual Loop Mode 743 MHz (PLL) 820 MHz (PLL) 80 MHz
[U]! Step frequency up by step size
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [U]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command increments the NCOUNTER and ACOUNTER fields of the A register for the currently targeted board. This steps up the PLL's frequency by the current step size for the board. If the currently selected board is an MC145220 in DUAL mode, then the currently targeted PLL on the board is "stepped". If the MC145220 is in SINGLE mode, then both PLLs on the board are "stepped".
[D]! Step frequency down by step size
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [D]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command decrements the NCOUNTER and ACOUNTER fields of the A register for the currently targeted board. This is the effect of stepping down the PLL's frequency by the current step size for the board. If the currently selected board is an MC145220 in DUAL mode, then the currently targeted PLL on the board is "stepped". If the MC145220 is in SINGLE mode, then both PLLs on the board are "stepped".
MC145220EVK 36 MOTOROLA
[O] Set PLL output frequency
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [O] is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command prompts the user to input a decimal value in MHz and kHz to set the targeted board frequency. The program default PLL output frequency is displayed along with the current value. The user may leave the output frequency value as is by entering return without entering a value. The program validates the entered frequency by checking to ensure that the value is a multiple of the board's current step size and that the entered frequency / frequency step size is 4032. The program accepts total divide values < 4032 if N A. (Total divide must be 262,143 for all PLLs.) N*P+A = total divide (p = prescale = 64 for '191), (p = prescale = 32 or 64 for '220) A further check is made to ensure that the entered frequency is within the capability of the currently targeted demonstration board. (See Table 7.) Frequencies outside the range are allowed for users who use their own VCO. Note in '220 dual mode, frequencies outside the program default will not be accepted due to the complexity of error checking the results.
A A A A A AAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Maximum Frequency 751 MHz 743 MHz 738 MHz 741 MHz 733 MHz 733 MHz 1482 MHz 1466 MHz 1466 MHz 1502 MHz 1486 MHz 1486 MHz MC145220 in Single Loop Mode MC145220 in Dual Loop Mode 733 MHz (PLL) 790 MHz (PLL) 60 MHz 743 MHz (PLL) 820 MHz (PLL) 80 MHz Once validated, the NCOUNTER and ACOUNTER fields of the A register are appropriately modified to set the PLL frequency for the targeted board to the specified value. If the currently targeted board is an MC145220 in DUAL mode, then the currently targeted PLL on the board will have its frequency set. If the MC145220 is in single mode, then both PLLs on the board will have their frequencies set.
MOTOROLA MC145220EVK 37
Table 7. Minimum Frequency
[F] Set REFin frequency and channel spacing
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [F] is on this screen.
See page 23 of this document for a sample screen shot of this command.
This command prompts the user to input two values. First, a decimal value, in the form of XX MHz + XXX kHz, to set the reference frequency of the targeted board. The program default frequency is displayed along with the current value. The user may leave the reference frequency value as is by entering return. A second input, in the form of XX MHz + XXX kHz, sets the channel spacing (step size) of the targeted board. The program default step size is displayed along with the current value. The user may leave the step size as is by entering return. The inputs are validated by checking that the step size remains 2 MHz ( 1 MHz for the '220) for all boards. The entered frequency is validated to ensure that the new reference frequency / new step size is < 8191 and is an even multiple of the new channel spacing. Finally, the RCOUNTER of the R register is set with the value of (new reference frequency / new channel spacing) and R register is written to the targeted board. Then the ACOUNTER and NCOUNTER are reset to the previous frequency using the new channel spacing (previous frequency / new channel spacing) and the A register is written out. Note that due to the complexity of error checking in dual mode, REFin frequency and channel spacing may not be modified.
AAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA
Board Type MC145190 MC145191 MC145192 MC145200 MC145201 MC145202 Default Step Size 100 kHz 100 kHz 100 kHz 200 kHz 200 kHz 200 kHz 10 kHz 14.4 MHz 14.4 MHz 14.4 MHz 14.4 MHz 14.4 MHz 14.4 MHz MC145220 in Single Loop Mode MC145220 in Dual Loop Mode 10.01 MHz 10.01 MHz 10 Hz (10.01 kHz (PLL), 10 kHz (PLL))
MC145220EVK 38 MOTOROLA
Table 8. Default Reference Frequency
[E] Set function of output A
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [E] is on this screen.
See page 25 of this document for a sample screen shot of this command.
This command displays a submenu with the next four options displayed if the currently targeted board is the last board in the cascade. The user may only change the Output A configuration on the last board in line. The user can select one of the following options to configure the Output A: [0]! Port Bits A23 and A22 (A22, A21 on '220) are set to 00 binary while the remaining bits of register A are preserved and the A register is written to the targeted board. Enable the [C][A] command. [1]! Data Out Bits A23 and A22 (A22, A21 on '220) are set to 01 binary while the remaining bits of register A are preserved and the A register is written to the targeted board. Disable the [C][A] command. [2]! fv Bits A23 and A22 (A22, A21 on '220) are set to 10 binary while the remaining bits of register A are preserved and the A register is written to the targeted board. Disable the [C][A] command. [3]! fr Bits A23 and A22 (A22, A21 on '220) are set to 11 binary while the remaining bits of register A are preserved and the A register is written to the targeted board. Disable the [C][A] command.
MOTOROLA
MC145220EVK 39
[N] Change C Register and Prescale
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [N] is on this screen.
See page 26 of this document for a sample screen shot of this command.
This command displays a submenu with the next seven options displayed. This is where the user can modify the C register settings. [0] Change output A - (Port) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [0] is on this screen. This is only available with Output A configured as a port for the currently targeted board. See [A][0]! command. Command not available in dual mode. [0]! Reset output A to 0 This resets the PORT field of register C (C1) to 0 and then writes register C to the currently targeted board. [1]! Set output A to 1 This sets the PORT field of register C (C1) to 1 and then writes register C to the currently targeted board. [1] Change output B (Out B) (not available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [1] is on this screen. Selects the logic state of output B. [0]! Reset output B to 0 This resets the OUTB bit of register C (C0) to 0 and then writes register C to the currently targeted board. [1]! Set output B to 1 This sets the OUTB bit of register C (C0) to 1 and then writes register C to the currently targeted board.
MC145220EVK 40
MOTOROLA
[2] Change PDout current with Output A defined as port (not available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [2] is on this screen. If A23, A22 are both 0 then the currently targeted board is set up as a port and the following sub- menu options are provided: [0]! 70% The PDout field of register C (bits C3 and C2) is set to 00 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [1]! 80% The PDout field of register C (bits C3 and C2) is set to 01 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [2]! 90% The PDout field of register C (bits C3 and C2) is set to 10 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [3]! 100% The PDout field of register C (bits C3 and C2) is set to 11 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [2] Change PDout current with Output A NOT defined as port (not available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [2] is on this screen. [0]! 25% The PDout field of register C (bits C3 and C2) is set to 00 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [1]! 50% The PDout field of register C (bits C3 and C2) is set to 01 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [2]! 75% The PDout field of register C (bits C3 and C2) is set to 10 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [3]! 100% The PDout field of register C (bits C3 and C2) is set to 11 binary while the remaining bits of register C are preserved and the C register is written to the targeted board.
MOTOROLA
MC145220EVK 41
[2] Change PDout current (only available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [2] is on this screen.
See page 27 of this document for a sample screen shot of this command.
[0]! 5% The PDout field of register C (bits C5 and C4) is set to 00 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [1]! 50% The PDout field of register C (bits C5 and C4) is set to 01 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [2]! 80% The PDout field of register C (bits C5 and C4) is set to 10 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [3]! 100% The PDout field of register C (bits C5 and C4) is set to 11 binary while the remaining bits of register C are preserved and the C register is written to the targeted board. [3] Change phase detector select To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [3] is on this screen.
See page 28 of this document for a sample screen shot of this command.
This command displays a submenu with the following options. It gives the user the ability to select which phase detector is selected. [0]! phi R & phi V Bit C6 of register C is reset to 0 while the remaining bits are preserved and the C register is written to the targeted board. [1]! PDout Bit C6 of register C is set to 1 while the remaining bits are preserved and the C register is written to the targeted board.
MC145220EVK 42
MOTOROLA
[3] Change phase detector (only available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [3] is on this screen. This command displays a submenu with the following options. It gives the user the ability to select which phase detector is selected. [0]! phi R & phi V Bit C2 of register C is set to 1 while the remaining bits are preserved and the C register is written to the targeted board. [1]! PDout Bit C2 of register C is reset to 0 while the remaining bits are preserved and the C register is written to the targeted board. [4] Change lock detect enable (not available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [4] is on this screen. This command displays a submenu with the following options. It gives the user the ability to change the lock detect setting. [0]! Output low Bit C5 of the C register is reset to 0 while the remaining bits are preserved and the C register is written to the targeted board. [1]! Enable output Bit C5 of the C register is set to 1 while the remaining bits are preserved and the C register is written to the targeted board. [5] Change phase detector polarity To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [5] is on this screen.
See page 29 of this document for a sample screen shot of this command.
This command displays a submenu with the following options. It gives the user the ability to change the output polarity of the phase detector. [0]! Non-invert PDout Bit C7 (C0 for '220) of the C register is reset to 0 while the remaining bits are preserved and the C register is written to the targeted board. [1]! Invert PDout Bit C7 (C0 for '220) of the C register is set to 1 while the remaining bits are preserved and the C register is written to the targeted board.
MOTOROLA
MC145220EVK 43
[6] Change standby To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [6] is on this screen.
See page 30 of this document for a sample screen shot of this command.
This command displays a submenu with the following commands available to set the STBY (standby) field of the C register: [0]! Normal operation The STBY field of register C (bit C4) is reset to 0 while the remaining bits of register C are preserved and the C register is written to the targeted board. [1]! Standby The STBY field of register C (bit C4) is set to 1 while the remaining bits of register C are preserved and the C register is written to the targeted board. [7] Change prescale (only available on '220) To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. Press [N], which will place you in the "Change C Register" screen. The command [7] is on this screen. This command displays a submenu with the following commands available to set the prescale: [0]! Prescale 32/33 The prescale is set to 32/33 while the remaining bits of the C register are preserved and the C register is written to the targeted board. [1]! Prescale 64/65 The prescale is set to 64/65 while the remaining bits of the C register are preserved and the C register is written to the targeted board.
MC145220EVK 44
MOTOROLA
[R] Set crystal/reference mode
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [R] is on this screen.
See page 32 of this document for a sample screen shot of this command.
This command displays a submenu with the following commands: [0]! Crystal mode, shutdown Bits R15, R14, and R13 of register R are reset to 000 binary while the remaining bits are preserved and the R register is written to the targeted board. [1]! Crystal mode, active Bits R15, R14, and R13 of register R are set to 001 binary while the remaining bits are preserved and the R register is written to the targeted board. [2]! Reference mode, REFin enabled, REFout low Bits R15, R14, and R13 of register R are set to 010 binary while the remaining bits are preserved and the R register is written to the targeted board. [3]! Reference mode, REFout = REFin Bits R15, R14, and R13 of register R are set to 011 binary while the remaining bits are preserved and the R register is written to the targeted board. [4]! Reference mode, REFout = REFin/2 Bits R15, R14, and R13 of register R are set to 100 binary while the remaining bits are preserved and the R register is written to the targeted board. [5]! Reference mode, REFout = REFin/4 Bits R15, R14, and R13 of register R are set to 101 binary while the remaining bits are preserved and the R register is written to the targeted board. [6]! Reference mode, REFout = REFin/8 Bits R15, R14, and R13 of register R are set to 110 binary while the remaining bits are preserved and the R register is written to the targeted board. [7]! Reference mode, REFout = REFin/16 Bits R15, R14, and R13 of register R are set to 111 binary while the remaining bits are preserved and the R register is written to the targeted board.
MOTOROLA
MC145220EVK 45
[T]! Set target PLL on board
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [T]! is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command is only available when the targeted board is a MC145220EVK, and that board is in single loop mode (see [B]! command). The MC145220EVK contains two PLLs, which are designated PLL and PLL. This command is a toggle function which directs the program to "steer" subsequent commands to either PLL or PLL on the targeted MC145220EVK.
[P] Set output port address
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [P] is on this screen.
See page 31 of this document for a sample screen shot of this command.
This command prompts the user to input a hexadecimal address of the printer port on their computer. This address is where the EVK boards are connected. The entered address is displayed on the main menu next to the [P] command prompt.
[G] Change board definitions
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [G] is on this screen. This command returns the user to the board definition screen. The user may then define a different cascade of boards.
[I]! Initialize board(s), write all registers
To access this command in the program, select a board in the "Define boards to program" screen and then press [Q]! . This will place you in the "Select from the available options" screen. The command [I] is on this screen.
See page 21 of this document for a sample screen shot of this command.
This command writes out all of the registers for all of the boards that are currently attached to the computer. The current settings are used for the registers. This correctly writes out the C, R, and A registers for each EVK board connected to the bus. In the case of MC145220EVKs, they are set to SINGLE (RESET/DEFAULT) mode and then have both PLL and PLL registers written.
[X]! Terminate demonstration program
This command is available on all screens within the program. This command causes the program to terminate and returns the user to DOS.
[?]! View help screen
This command is available on all screens within the program. This command displays the help screen.
MC145220EVK 46 MOTOROLA
APPENDIX
MC145220 PLL Evaluation Board
MOTOROLA
MC145220EVK 47
MC145220 Power Supply and Reference
MC145220EVK 48
MOTOROLA
MC145220EVK Bus Interface
MOTOROLA
MC145220EVK 49
MC145220EVK Signal Plot -- Dual Loop Mode Output at 70 MHz
MC145220EVK Signal Plot -- Single Loop Mode PLL on 805 MHz
MC145220EVK 50
MOTOROLA
MC145220EVK Signal Plot -- Single Loop Mode PLL on 738 MHz
MOTOROLA
MC145220EVK 51
Bill of Materials MC145220 PLL Evaluation Board Rev. 4
Part 2SV-02 50-651-0000-31 51R05279V17 76SB08S 617Y-025SAJ120 3266W1-103 Capacitor Capacitor Capacitor Type Pwr Connect SMA Female VCO Logic Switch DB-25 Female Trim Pot. 5% NPO 5% NPO Ceramic Package Special Special Special 16-Pin DIP Special Special 0805 0805 0805 Manufacturer Augat ITT Sealectro Special Grayhill Amphenol Bourns 10 k 0.001 F 0.02 F 0.1 F Value Quantity 1 4 1 1 1 2 4 1 10 J8 J2, J5, J10, J12 M2 S1 J9 VR1, VR2 C6, C13, C20, C27 C24 C3, C5, C8, C11, C18, C23, C28, C31, C32, C34 C26 C29 C21 C22 C15 C4, C12, C14, C17, C33 C7 D4 D1, D2, D3 U4 L2 L1 J1 M5 U5, U6, U7 U2 U1 R6, R26 R4, R7, R8, R12, R24 R15 R22 R1, R18, R21 R33 R3 R5, R9 R13 R10, R36 R25 References
Capacitor Capacitor Capacitor Capacitor Capacitor Capacitor Capacitor HLMP-6001-011 HSMS-8101 INA-10386 Inductor 1008CS Inductor 1008CS Jumper KXN1142AA SP01 LM317MDT MC74HCT241ADW MC145220F Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor
5% NPO 5% NPO 5% NPO 5% NPO 5% NPO 5% NPO 5% NPO LED Diode
0805 0805 0805 0805 0805 0805 0805 Special SOT-23 HP HP HP 1008 1008 Coilcraft Coilcraft
0.15 F 10 47 75 82 100 3000
1 1 1 1 1 5 1 1 3 1
33 nH 47 nH
1 1 1
2 x 1 Header Saber TCXO Regulator Octal Buffer PLL IC 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF
0.1 Grid Special Special SO-20 SOG-20 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 Motorola Motorola Motorola Motorola 0 1k 3.3 3.3 k 10 k 16 18 k 20 k 47 51 100 14.4 MHz
1 3 1 1 2 5 1 1 3 1 1 2 1 2 1
Continued on next page
MC145220EVK 52 MOTOROLA
Continued from previous page
Resistor Resistor Resistor Resistor Resistor Resistor Resistor RTVXO-231BX SN74LS126D TDC-105K050NSE TDC-336K010NSF TUF-2SM URAE4-417A Wire Jumper Wire Jumper 2-Way SJ5027SPBL 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF 5% CF TCXO Quad Buffer Tant. Cap. Tant. Cap. Diode Mixer VCO 0.6, 24 AWG 0.6, 24 AWG Rubber Bumpers 3M Special 0805 0805 0805 0805 0805 0805 0805 Special SO-14 Special Special Raltron Motorola Mallory Mallory Mini Circuits Alps 1.0 F, 50 V 33 F, 10 V 120 160 180 300 430 910 1800 10.01 MHz 1 1 3 5 1 1 1 1 1 1 2 1 1 2 1 5 R23 R14 R11, R16, R34 R27, R32, R37, R46, R48 R35 R29 R28 M1 U3 C30 C2, C10 M4 M3 J3, J4 J11
NOTES: 1. J11 connects V+ to + 5 V. 2. Test point holes should not be filled with solder. 3. The rubber bumpers must be glued on bottom side of board in the four corners and in the center. 4. Do not wash the board.
MOTOROLA
MC145220EVK 53
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MC145220EVK 54
*MC145220EVK/D*
MC145220EVK/D
MOTOROLA

▲Up To Search▲

Price & Availability of MC145220EVK

	To Download MC145220EVK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .